Maintenance service

With all the mechanical tools, the use of the process may be loose, causing the vehicle parts abnormal sound. You should regularly check the tire pressure, tire screw and other parts of the loosening of the screw. Wing thinking in the cleaning process, can not directly flush, can use a damp cloth to wipe or brush dirt place. The screw can be regularly used to maintain the appropriate care oil to prevent corrosion. Please keep the vehicle in a cool and ventilated place for a long time.

Caiqiees2.0 maintenance knowledge

Model: caiqiees2.0

I. caiqiees2.0 EU representative
LUQI INTELLGENT TECHNOLOGY CO., LTD 95 HIGH STREET OFFICE B GREAT MISSENDEN HP16 0AL U
Tel.: + 44 203 4681 833    Fax: + 44 020 3475 4138    Email: luqi@zjluqi.com
 

III. basic parameters of caiqiees2.0 vehicle
Maximum speed: 40km / h mileage: 71km motor: 1200W wheelbase: 1360mm maximum load: 175KG battery: 60V 20Ah tire size: 12 inches

Maintenance Tips:

1. The electric bicycle shall be maintained every half a year, the transmission parts shall be lubricated and rustproof, all fasteners shall be strengthened, and the tightness of spokes shall be adjusted.
2. When charging the battery, first insert the output plug of the charger into the battery box, and then connect the input plug of the charger into the electric socket in the room. Constant current, constant voltage, floating charge three-stage automatic switching mode is adopted for charging. When the battery reaches the sufficient level, it will automatically switch to floating charge without manual control of charging time. When not charging, do not connect the charger to the AC power supply without load for a long time. If the grid voltage fluctuation in the user area exceeds 15% of the normal value, it is recommended to configure a household appliance voltage regulator. The battery has a certain service life. If the driving mileage is less than 50% of the rated mileage after a full charge, the battery generally needs to be replaced. The replacement battery must be replaced in the special maintenance center, and the old battery must be handed over to the maintenance center for unified treatment.
3. During maintenance, any problems in motor, battery, control system and charger shall be repaired in the special maintenance center, and shall not be disassembled casually

Repair maintain

The balance of the car accidentally a small amount of water after, please immediately turn off the power switch, transport vehicles or support to a safe place, contact Sony Company Sales Department Service guidelines.

Lukehl electric vehicle warranty

In order to effectively protect your legal rights, improve the civil liability system for product quality, and facilitate the performance of the three guarantees obligation and responsibility, please properly keep the maintenance card. With the card and the purchase invoice, you can get the Three Guarantees service from the car seller.

I. Three Guarantees principle
1. When you purchase a car, you have the right to ask the sales staff for correct use methods and maintenance matters, and provide effective invoices, maintenance cards and maintenance units, addresses and contact numbers.
2. The user shall operate and use the product correctly according to the product manual. In case of performance failure due to manufacturing quality, it shall be in accordance with the law of the peoples Republic of China on domestic quality. According to the law of the peoples Republic of China on the protection of consumers rights and interests and the provisions of the state on three guarantees for products, each agent of the company shall perform the three guarantees obligations:

II. Other items not covered are vulnerable parts, and corresponding cost shall be charged for replacement.

III. vulnerable products, consumables and plastic parts are not covered by the warranty.

IV. if you need maintenance, you must go to the special maintenance center designated by the factory for maintenance, otherwise you will be responsible for all consequences.

V. the final interpretation right of the warranty terms belongs to the company.
Scope and content not included in "Three Guarantees":

1. Failure caused by the users failure to use, maintain and adjust in accordance with the "operation manual".

2. Failure caused by users non-compliance with the use regulations.

3. Faults caused by improper storage or accidents of users. (damage caused by impact, car falling, over speed, over load and chemical corrosion)

4. The user can dismantle, change or replace the fault caused by the non companys special accessories (battery, motor, controller, sensor) without permission.

5. The repairer who is not responsible for "Three Guarantees" breaks down and causes damage;

6. The appearance is damaged after sale; the vehicle is damaged due to force majeure;

7. The following vulnerable products, consumables and plastic parts are not covered by the warranty: brake block (leather), foot pedal, brake line, sensor, flasher, fuse, bulb, speedometer, buzzer, reflector, socket, horn, rearview mirror, harness, plastic parts, mud board, chain cover, ball frame, steel ball, lamp, inner and outer tire, standard parts, etc

8. There is no maintenance card, and the invoice or ticket card is inconsistent.

9. The warranty parts shall not be replaced for free if they are damaged artificially or beyond the three guarantee period.

10. The cost of self repair without the consent of the special maintenance unit.



hot tip：

1. Regulations on wading: when the vehicle passes the road with accumulated water in rainy days or travels through water in normal times, the wading depth shall not exceed the radius of the rear wheel (motor), and it is not allowed to spray with a water gun when washing the car. If the user violates this regulation, resulting in water in the motor, short circuit of internal coil, falling off of magnetic steel or short circuit of water in the controller, he will not enjoy the quality assurance service.

2. Regulations on serious overload: or those who lose the use function will not enjoy the quality assurance service.

3. It is not a quality problem, and it cannot be returned or replaced.

4. The tools and certificates provided with the car shall be checked in time, and the company or the dealer shall not reissue them.

5. If you have any questions during riding, please contact our company or authorized dealer immediately. We will provide you with timely, high-quality and efficient services.

Quality Supervision

When the vehicle is in the process of alarm, the safety warning is generated according to the factors such as the speed of the vehicle, the load of the vehicle, the riding angle and the road condition. When the above happens, please pay attention to driving safety, do not speed.

A qualified luki Harley car has to go through many rigorous and complex processes before leaving the factory. 1. The product sketch design is to be finalized. 2. The development department coordinates the trial assembly of the sample car with respect to the iron frame, power, lamps, lines and instruments. 3. The appearance mold production, the iron frame mold production and the lamps mold production. 4. The trial assembly, the road test, the modification and coordination. 5. The mass production plan notice is issued before the production and after the production Strict purchase of raw materials, training of tooling personnel, offline inspection, strict packaging and delivery, in which each vehicle of EEC standard shall be equipped with COC certificate as standard, and the VIN frame number and engine number corresponding to the vehicle shall be presented on the document. The VIN frame number of Lugi ex factory Harley vehicle is arranged as follows:

 sljc2000xj1xxxxxx